The Council Tool Jersey Classic Axe – Part 2

If you haven’t already done so, check out Part 1 for my overview of this axe and the modifications I made to it.

Before I tested the Jersey Classic axe from Council Tool, I decided to paint the phantom bevels because I could not get the patina dark enough to match the rest of the bevels. Hence the different appearance in the pictures below as compared to the previous pictures. Ultimately, I decided to remove the paint and smooth out the bevels to remove the drop-forging marks entirely.

I started the testing with bucking. The tree I chose was a spruce which blew down in a tornado a few years back and was well seasoned. It was also completely frozen (the temperature was about -17*C/1.5*F). The part of the tree I bucked measured 20 cm/8″ in diameter. It took about 50 chops to get through the spruce (I was not very experienced with an axe this large when I did this initial testing, which was about 2 years ago). I ended up bucking another section of the log half-way through in 20 chops. For good measure, I bucked another piece almost completely through. The axe showed itself to be quite accurate. The slight head misalignment proved to be a non-issue.

Next up was limbing. Most of the 2.5 – 5 cm/1 – 2” limbs were sliced off in one swing.

While cutting off the last limb, I heard a noise that made me cringe: tink! It was the blade kissing a rock.

Tsk-tsk-tsk. I thought there was only snow underneath the tree, but unfortunately this was not the case. To my delight, the metal deformed instead of chipping…and at -17*C/1.5*F! I’m sure some axes would have chipped. When I got home later, I spent a minute or two with a file to fix up the edge. I couldn’t fix it out in the woods, though, but I pressed on anyway.

I proceeded to split one of the bucked bolts next. This went really quickly, and I had six pieces of split wood from a total of 10 swings.

Finally, I decided to fell a small dead tree. The tree I picked was a 9 cm/3.5”-diameter dead frozen pine. I didn’t fell a larger tree because I was running out of daylight, couldn’t find a larger dead tree and didn’t want to fell a larger live tree without the landowner’s permission. Suffice it to say, the axe made short work of the pine. 3 – 4 chops on each side and it was down.

Throughout this testing, the axe performed well, was easy to handle and was less fatiguing to use than I had expected (having mainly used smaller/lighter axes up to that point). I was very pleased by how deep the blade bit into the wood thanks to its thin (in comparison to hardware-store axes) profile. Overall, I was very pleased with this axe.

In the months following this initial testing, I used the axe to process several similar trees into firewood. On one particular winter outing, I noticed that the head was creeping up the handle. After working some more, I managed to move the head halfway off the handle! I contacted Council Tool about this, and while my contact person was talking to the management, I got impatient and decided to fix the problem myself. Even if they had offered to fix it for me, I didn’t want to go through the process of boxing it up, sending it overseas, having them fix it and then wait to receive it (again). I had to cut a few inches/centimeters off the top of the handle after drilling and prying to get the aluminum wedge out, but this length difference didn’t seem to affect the axe too much. Since fixing the tool, I haven’t had any more problems with the head moving (I used wooden and steel wedges for the job).

It’s hard for me to say whether or not I recommend this axe, not because of the material quality (which is high) or the overall workmanship (which is good), but for the obvious reason of the head-attachment problem I experienced. If you can fix something like this yourself, then it’s no problem. If you can’t or don’t want to, it’s a different story (though if you use an axe a lot, you should be able/willing to). Hopefully, mine was just a dud! If this problem is not common on Council’s axes, then your money is definitely well spent when you buy one!

About these ads

9 comments on “The Council Tool Jersey Classic Axe – Part 2

  1. [...] real test for any tool, of course, is how well it works, so check back soon for Part 2, where I’ll cover my experiences in felling, limbing, bucking and splitting with the Council [...]

  2. Sam says:

    Wow that looks cold!!!

    You have a great looking axe there, it did a fine job on that spruce. I know how it is to hit a rock like that, but it looks like it held up well. Is spruce very hard to work with?

    • Eh, it’s not that cold for Finland. :) I’ve been in the woods at temperatures down to about -30*C/-22*F and doing other things outside down to -40*C/-40*F. :) At that point it starts to feel a little chilly. ;)

      Overall, spruce isn’t a tough wood to work with, but when it’s seasoned and frozen, it’s not the easiest either. The tough knots can make splitting a real chore sometimes.

  3. OutdoorEnvy says:

    I’ve heard of that aluminum wedge coming loose before on those. It’s an easy fix if you know what you’re doing. Good review. I liked the wide range covered for axe use.

    • The aluminum wedge on mine didn’t come loose. In fact, it hardly came out at all. The head just slowly rode up the handle. Since the AL wedge is serrated, it wasn’t possible to add wooden wedges to tighten up the fit, so it had to be fully removed and replaced.

      Thanks for the comments!

  4. Great post- How did their customer service play out in the end?

  5. Karson Branham says:

    Great review!! Thanks for taking time to share. I have used axes a lot in the woods, growing up and now at our tree farm in NW Oregon. I really like the CouncilTool line of axes. I am thinking of a 5# or 6# Dayton pattern with a 28″ straight handle to use as my main splitting axe. Will be lighter than the maul and I think more effective. Definitely less work.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s